1F
Clutch failure. Machine has failed to start to agitate. Press the start / pause button to see if machine will restart. If unsuccessful, requires service call. Phone 13 13 49.
2F
Motor temperature sensor failure. Motor overheated. Wait 10 minutes to see if problem goes away. If not contact service on 13 13 49.
3F
Motor speed (position) sensor failure. The motor cannot run. Advance to SPIN and press start / pause to drain water from bowl. Contact service on 13 13 49.
AF
Internal PC board failure. Requires service call. Phone 13 13 49.
CO
PC board communications failure. Requires service call. Phone 13 13 49.
DD
Drip dry has been selected instead of spin. Select spin speed and close lid. 
DE
Machine has been programmed for delay start. If Delay start not required press start / pause button to cancel. 
DF
Water temperature sensor failure. Requires service call. Phone 13 13 49.
EE
EEPROM failure. The machine is not operational and requires a service call. Phone 13 13 49. 
FL
Flooding fault. If there is water pouring into the bowl, turn off wall taps and turn off the machine. Requires service call - phone 13 13 49. If no water coming into machine wait for this fault to self-clear. 
FN
Not an error. This means cycle has completed.
Ld
Lid not closed. If Closed problem with lid switch circuit. Requires service call. Phone 13 13 49.
LL
Unexpected water loss. If water is pouring onto the floor advance to spin and press START/PAUSE. May require service. Phone 13 13 49. 
OB
Off balance load. Rebalance load.
PF
Pressure sensor failure. Level sensor fault. Advance to SPIN and press start / pause to drain water from bowl. If required phone service on 13 13 49.
PU
Draining problem. Pump blocked or failed. Requires service call. Phone 13 13 49.
SF
PC board has detected the spin bowl is not spinning fast enough. Could be possible suds lock. Try to start cycle with no clothes and allow machine to complete cycle to flush and disperse suds. Please reduce amount of detergent used.
SL
Suds lock. Start cycle with no clothes and allow machine to complete cycle to flush and disperse suds. In the future try to reduce detergent amounts.
SO
Machine in soak Mode. Press soak button repeatedly till 00 is displayed.
SP
Machine in pause mode. Press start / pause to resume.
TF
Motor has overheated. Maybe suds locking due to using too much detergent. Reduce amount of detergent. The motor may cool down and the fault will self clear. If the fault does not self clear and there is water in the bowl the machine can be advanced to spin to operate pump and empty bowl. Service call required. Phone 13 13 49.
Banging noise - noisy in spin
Brake operation at end of spin segment of program. This noise is normal and is the brake lever stopping the spin bowl from turning.

Load slightly off balance. Rebalance load.
Noisy in spin -rattling noise in spin
Vibration during spin causing the drain and / or inlet hoses to tap against the back of the machine. Reposition hoses.
Banging noise when filling
Water hammer when the water valves close. Not a product fault. Water pipes are moving in the wall. Try and turn down water at house supply tap.
Banging noise when lid opened during spin
Brake operation during spin segment of program. This noise is normal and is the brake lever stopping the spin bowl from turning.
Noisy when draining - noisy when pumping
Pump cavitation. This is a rhythmic droning / slurping noise when most of the water has been pumped out. This level of noise is normal and it occurs when most of the water is drained and air is being sucked into the pump. This does not harm the machine.
Noisy during spin
Bra wire could be caught between inner and outer washbowls. If bra wire is visible remove with pliers.
Noisy during wash
It is normal to hear a slight whirring noise as the agitator moves. This is normal operation.
Noisy when filling
Tap or valve whistling due to water pressure. Close the tap a little bit.

Water hammer when the water valves close. Not a product fault. Water pipes are moving in the wall. Try and turn down water at house supply tap.
Rattling noise in spin
Drain and / or inlet hoses hitting back of machine. Reposition hoses.
Vibrating - noisy in spin
Load slightly off balance. Rebalance load.

Machine not levelled correctly causing excessive bowl and / or panel vibration. Adjust levelling legs so machine is level.                         
Banging noise in pipes
Water hammer in the pipes when the water valve closes. Not a product fault. Water pipes are moving in the wall. Fit anti hammer device, available from plumbing supplies and hardware stores or have a plumber fit a pressure reducing device.

 

Bowl dropped - bowl lower when loaded
Normal - weight of water and clothes compresses the suspension causing the bowl to drop down. This is not a product fault. The bowl will return to its normal position once the wet clothes are removed at the end of the program.
Clothes tangled
Incorrect water level for size of load. If water level is too high for the load size the clothes can bunch up and tangle. Use lower water level.
Clothes tangled around agitator
Clothes not loaded correctly. Position clothes evenly around the agitator. Do not wrap large items around agitator.
Clothes too hard
Too much detergent being used and not fully rinsing out.

Clothes over dried on line or in dryer. Shorten drying time.                         
Clothes wet at end of program
Outlet / drain hose kinked not allowing all the water to be pumped out. Check for kinked hoses.
Cycle / program taking too long
Filters blocked slowing the water entry. Machine will take longer than normal to fill. Clean filters in the inlet hoses.

Inlet hose kinked slowing the water entry. Machine will take longer than normal to fill. Unkink hose.

Compared to older machines program times are longer. This allows larger capacity wash loads to be washed to the same or better standard than older machines with smaller capacity loads using the same or less quantity of water.
Dirty wash - stains
Not enough or no detergent. Check amount of detergent used and rewash clothes.

Too many clothes in load. Remove some clothes and rewash.

Incorrect wash program or temperature selected. Reselect program and or temperature.

Incorrect water level selected. Use higher water level and rewash clothes.

Fabric conditioner on clothes. Looks like oil. If stain can be washed out by hand then it may be fabric conditioner and not oil. Clean out appliance with washing soda.
Filling and emptying immediately
If outlet hose is lower than the water level on machine the water will continue to syphon / run out of hose on fill cycle. Move hose to top of the machine. Refer to user manual.
Lint on clothes
Low water level. Increase water level.

Lint filter bag torn or missing. Replace filter bag. Available from Spare Parts. Phone 13 13 50.

Mixed load. Follow correct procedure for sorting loads. Refer user manual.

Fabric softener has blocked off holes in lint filter material. Clean lint filter in warm water.

Lint filter not cleaned.

Machine overloaded. Reduce wash size.
No rinse - only spin
Eco rinse option selected (if available). Eco rinse is a series of spray rinses. 4A water rated models default to eco rinse. Select deep rinse option.                  
Not advancing - will not finish program
If outlet hose is lower than the water level on machine the water will continue to syphon / run out of hose on fill cycle. Move hose to top of the machine. Refer to user manual.

Out of balance load. Redistribute clothes evenly. 
Not draining - before deep rinse
Suds save option selected (if available). Change option.               
Not draining - before final spin
Drip dry option selected (if available). Change option. 
Not draining - draining slow
Pump suds lock caused by too many suds. Pause the program and let the machine sit for a while until suds subside then restart the program. Reduce the amount of detergent being used.           
Not draining - draining slow - water left in the machine
Drain hose kinked. Adjust hose.
Not filling
Not at start of wash program. Turn program knob to start of wash cycle.

Filters blocked. Clean filters in the inlet hoses.

Inlet hose kinked. Unkink hose.

Hoses connected to wrong taps. Connect hoses to correct taps.

Ensure taps are turned on.

Ensure lid is closed.                                          
Not filling, emptying immediately
If outlet hose is lower than the water level on machine the water will continue to syphon / run out of hose on fill cycle. Move hose to top of the machine. Refer to user manual.
Not spinning
Machine overloaded causing motor to overheat. There may be a burning smell as well. Reduce the size of the load. The motor will restart once it has cooled down.

Out of balance load. Redistribute clothes evenly.

Lid not closed. Close lid.                                                            
Not spinning - not rinsing
Too many suds causing motor to overheat. There may be a burning smell as well. Use less detergent and / or use a low suds detergent eg front load washer detergent. If doing another load allow 20 minutes before starting to let motor cool down.
Not washing - not agitating
Too many suds causing motor to overheat. There maybe a burning smell as well. Use less detergent.

Machine overloaded causing motor to overheat. There may be a burning smell as well. Reduce the size of the load. The motor will restart once it has cooled down.

Ensure lid is closed.

Program in soak period. Wait until soak period finished. If electronic machine it may have a programmable soak period. Cancel soak period.                  
Not working
No electricity supply through the power point. Check power point with a small appliance that you know works.

Ensure water taps are turned on.

Out of balance switch off. Re-position clothes evenly around the agitator in the wash bowl.

Ensure machine power button has been switched on.

Delay start set (if available). Cancel delay start.
One way agitation - agitator only moving in one direction
Normal bowl rotation during fill. Some models slowly rotate the bowl while at the beginning of the filling process. This is normal.                               
Slow filling - taking too long to fill
Filters blocked. Clean filters in the inlet hoses.

Inlet hose kinked. Unkink hose. 
Machine spinning when filling
Normal bowl rotation during fill. Some models slowly rotate the bowl while at the beginning of the filling process. This is normal.                             
Will not return suds
Obstruction in the trough blocking the suds hose. Remove blockage.

The suds hose may be kinked or flattened. Unkink hose.  
Burning smell
Too many suds causing motor to overheat. Use less detergent and / or use a low suds detergent eg front load washer detergent. If doing another load allow 20 to 30 minutes before starting to let the motor cool down.

Machine overloaded causing motor to overheat. Reduce the size of the load. If doing another load allow 20 to 30 minutes before starting to let motor cool down.                         
Going out of balance
Incorrect water level for size of load. If water level is too high for the load size the clothes can bunch up on one side. Use lower water level.

Clothes not loaded correctly. Position clothes evenly around the agitator. Do not wrap large items around agitator.

Machine not level. Adjust levelling legs.                         
Vibrating - moving across floor
Machine not level. Adjust levelling legs.

Floor too slippery eg high gloss tiles. Contact Spare Parts on 13 13 50 and request Non Slip Discs (Part Nº 8000777477).

 

Water on floor - flooding / leaking
Incorrect water level for size of load. If water level is too high for the load size it will cause splashing. Use lower water level.

Condensation from hot water running down the inside of the machine & dripping on the floor. Reduce water temperature.

Spin cycle selected before water pumped out. Select drain before spin cycle.

Loose inlet hose connections or washers / filters missing. Check connections at taps and at rear of machine.

Machine is tilted forward. Water coming into the machine is hitting the bowl cover. Level by raising the front or lowering the rear of the machine.

Tap leaking. Check taps.